enginph
-
Posts
2,861 -
Joined
-
Last visited
Content Type
Profiles
Forums
Calendar
Posts posted by enginph
-
-
I have some noise from inside the door. Couldnt find the source, something inside. It makes it on rough roads..
-
I used to have that, from memory it is to do with the tail light bulbs. One is probably out, or converted to LED.
The funny thing is one rear LED was out and I replaced outer 2 just before this starts happening. However I had LEDs for years and never had this problem. How did you fix it? One inner LED is half working now. Maybe I should replace them as well. And also one front parking bulb is out. It is regular bulb.
-
What is the mileage again?
I have a weird problem. When I step on the brakes the gauge illumination goes to night mode
-
I rented a hyundai elantra and it was surprisingly good. I couldnt find anything to complain, given the segment of course. I ride quality is very good yet handling/brakes were not compromised. Audio is far better than an average japanese sedan. Everything was firm no panel squeaks, unlike mazda3, 6.
Should try sonata.
-
I used 5w-40 and 10w-30 amsoil. I dont see any difference in terms of: oil consumption, mileage, performace.
40 is better if you drive at high revs and let more fuel mix to the oil, causing oil to get lighter. M3 uses 10w-60 and regularly revs above 5k rpm. If you dont race with hold pressed I dont think you usually drive at high revs with an AT car.
-
I was one of the first people in North America to drive the Mazda2 awesome little b-car. Handles really well.
Handles well? I can roll it like an egg with those bicycle tires.
The actual 2 looks very cheap with lots of plastic. The photos I posted belonged to the show car in LA auto show which looks at least stylish.
-
Wait for icar.
-
Mounts cause rather noise than vibration. MCE doesnt vibrate anyways
I had all 4 mounts broken (all changed), the cost is in the ball park of $1000. -
-
Ice breaker, the thing stops the party.
Kind of reminds me of the kia soul, but without the gerbals
What a stupid commercial..
http://www.youtube.com/watch?v=xr9zoWVSZDI
-
You basically wanna put another V6 there. Ever pop the hood of your car??
-
I bet its a coil. Happened to me in humid before. Sure its random??
I will share the short ram pix. It is awesome. Now people ask where was that plane when I floor
You should do it!! -
audi what?
-
No, per your advice I looked into it already and have gotton detailed instructions, as well as the correct kevlar replacement so it may go 100k, along with while doing the replacment change out the tensioner and replace waterpump with metal blade one to keep from issues in the future
What they used plastic blades?
-
Some 01 and all 02 milleniae have larger diameter brake rotors. To put them they changed the knuckle which holds the bearing. The axle is also different. You likely have the larger diameter brakes, new brake calipers, knuckle and new sized wheel bearing. If you remove the wheel cap and measure the axle nut size there I can tell you if you have the new set.
If this is the case you should look for a 01-02 (millenia) knuckle/bearing.
So you cannot read the part number on mazda supplied new part?
Hi,
I went to measure the axle nut and with my rudimentary measuring tool I found it to be approximately:
Outer Diameter - 45mm
Hole - 21mm
Basically I turned the nut around and measured its reverse flat surface. If you want me to post some pictures of it being measured with my ruler in order to highlight any inaccuracies that I may have made, then please do let me know.
Thanks in advance for your advice.
Regards.
It should be either M30 or M36. It says standard M30 has 45mm outer diameter. So it is likely that you have the smaller sized axle (95-00 millenia). 21mm hole should be a wrong measurement, or I am misunderstanding where you measure. I will double check mine when I have the time.
-
Some 01 and all 02 milleniae have larger diameter brake rotors. To put them they changed the knuckle which holds the bearing. The axle is also different. You likely have the larger diameter brakes, new brake calipers, knuckle and new sized wheel bearing. If you remove the wheel cap and measure the axle nut size there I can tell you if you have the new set.
If this is the case you should look for a 01-02 (millenia) knuckle/bearing.
So you cannot read the part number on mazda supplied new part?
-
Does he have this bumper sticker?
It comes with the sticker right?
-
Why is that necessary when the car is mostly stationary.
My cars are made to run, not to stop
- Ettore Bugatti
Seems like Toyoda recently adopted this philosophy.
-
or Prius
He already admitted that on his video right? -
What is the part number?
-
Sounds like ///BHRpowered is buying a Toyota.
I bet he has a daily drive camry.
-
Hello
My name is miss Judith.i saw your profile today at (forums.mazdaworld.0rg)and became intrested in you,i will also like to know more about you,and i want you to send a mail to my email address so that i can give you my picture for you to know whom l am.Here is my email address (judith_20096@yahoo.co.uk) .i believe we can move from here.I am waiting for your mail to my email address above.Remeber the distance or colour does not matter but love matters alot in life) please send me mail to my e mail address.
Please reply me with my email address here
(judith_20096@yahoo.co.uk)
-
it is petroleum jelly....What would that do to a car?
Oh you were talking about cars?
-
no, I've heard somewhere that vasoline is a good replacement for Armor all and other protectants....anyone ever tried it? supposeably you can apply a thin coat to bring back luster and shine.....
man no matter how i write that it just comes out bad.....LOL
Dude vaseline is not a protectant
Window Noise When Going Down
in Millenia / Eunos 800 / Xedos9
Posted
So the question is why didnt they put an auto up switch?